OMS Opto Chemicals

Bevel Edger Coolant
Material Safety Data Sheet

oms_image.GIF (3520 bytes)

Google
SECTION 1: MANUFACTURER INFORMATION
WHMIS classification D2B
UN number not regulated
Packaging group n/a
Product name generator coolant
Chemical formula proprietary
Chemical family oil
Material use emulsifiable grinding oil and coolant
Emergency telephone 514-738-6637, TOLL FREE: 800-461-6637, BUSINESS HOURS.
cas mixture
SECTION 2: HARZARDEOUS INGREDIENTS
Product % t.l.v. c.a.s.# lc50 route species lc50 route, species
Bevel edger coolant at 100%   mixture   rat >4000.0 mg/kg

rabbit>1900.0 mg/kg

Ethanol,2-(2-butoxyethoxy) 1.0-5.0%   112-34-5    
Sulfonic acids,petroleum, sodium salts 1.0 - 5.0%   68608-26-4    
9-octsdecenamide,n.n-bis(2-hydroxyethyl) 1.0 - 5.0%   93-83-4    
SECTION 3: PHYSICAL DATA
Boiling point n/a
Physical state liquid
Odour n/a
Vapour pressure (mmhg) n/a
Vapour density air=1 n/a
Freezing point n/a
Spec.gravity (h20=1) <0.95
Evaporation rate n/a
Water solubility complete
pH 8.7
SECTION 4: FIRE AND EXPLOSION HAZARD
Flammability n/a
Flash point c, method >154 pensky martens cc
Auto ignition temp. n/a
Unusual fire and explosion hazard n/a
Extinguishing data dry chemical, carbon dioxide, foam, water spray,
Special fire fighting procedures use water to cool fire exposed containers. water or foam may cause frothing.
SECTION 5: REACTIVITY DATA
Chemical stability stable
Compatibility with other substances, yes  
no, which ones strong oxidizing agents
Conditions to avoid avoid excessive heat. formation of vapours or mists.
Hazardeous polymerisation will not occur
Hazardeous decomposition products carbon monoxide, carbon dioxide, oxides of nitrogen, oxides of sulphur.
Comments  
SECTION 6: TOXICOLOGICAL PROPERTIES
INFORMATION: INFORMATION FOR THIS PRODUCT IS BASED AT 100% CONCENTRATION OF HARZARDEOUS INGREDIENTS
Skin contact  
Skin absorption  
Eye contact irritating
Inhalation inhalation of oil mists or vapours from hot oil may cause irritation of the upper respiratory tract.
Swallowing, ingestion ingestion will cause nausea, vomiting, diarrhea.
Effects of acute exposure  
Effects of chronic exposure long term intensive exposure to oil mists may cause benign lung fibrosis. prolonged or repeated contact may cause various forms of dermatitis including folliculitis and oil acne.
Irritancy of material see above
Carcinogenicity n/av
Reproductive effects n/av
Biological monitoring  
Supplemental health information Testing completed with this product indicates that it is irritating to the eyes. Data is insufficient to further classify according to WHMIS criteria.
  PREVENTATIVE MEASURES
Gloves/type chemical resistant gloves, rubber
Clothing apron or clothing to protect skin
Respiratory type If respiratory irritation is experienced, use an approved air purifying respirator. If exposure exceeds occupational exposure limits, wear a niosh-approved respirator. Depending on measured levels, a mechanical filter, air purifying respirator for mists or air supplied respirator is recommended.
Eye/type chemical safety goggles, face shield.
Ventilation adequate ventilation to maintain 1 PPM
Waste disposal in accordance with municipal, state or federal regulation
  FIRST AID MEASURES
instructions: eyes: immediately flush eyes with water for at least 15 minutes while holding eyelids open. if irritation occurs or persists get medical attention
  skin: wipe excess from skin. wash contaminated skin with mild soap and water
  oral/ ingestion: do not induce vomiting. seek immediate medical attention.
  inhalation: remove to fresh air, restore and or support breathing, seek medical attention if respiratory irritation occurs or if breathing is difficult.

in case of ingestion: do not induce vomiting obtain medical attention immediately.

primary route of ingestion inhalation or ingestion. skin contact, eye contact
notes to physician In general, lubricating oils have low oral toxicity. High pressure injection under the skin may have serious consequences and may require urgent treatment.
SECTION 7: ACCIDENTAL RELEASE MEASURES
  Disposal of collected product, residues and cleanup materials may be government regulated. Observe all applicable local, state/provincial, and federal waste management regulations. Mop up, or wipe up, or soak up with absorbent and contain for salvage or disposal. for large spills, provide diking or other appropriate techniques, such as several moppings or swabbings with appropriate solvents; washing with mild detergents or solutions or high pressure steam for large areas. Use typical industrial cleaning materials.

Local, state/provincial and federal requirements may apply to spills or releases of this material into the environment.

SECTION 8: PREPARATION OF INFORMATION
Emergency telephone 514-738-6637 OR TOLL FREE 800-461-6637, business hours
Prepared by: C.Ryser

REVISED 05/31/2008

Back to OMS Opto Chemicals Home Page

http://optochemicals.com

 

 

OMS, 177108 Canada Inc.
97 Columbus
Pointe Claire, Québec
Canada
H9R 4K3
Telephone Fax Toll Free Telephone
514-426-3055 514-426-1138 800-461-6637
Please add long distance and country code number where necessary.

E-mail us!
E-Mail Us!

e-mail address:  oms_optical@yahoo.com